Health and Safety Terms, Definitions and Abbreviations
A plain guide to health and safety terms and definitions, with an occupational health and safety glossary and the abbreviations you will meet on signs and forms.
Contents
- Why a shared health and safety glossary matters
- Hazard and risk are not the same term
- What a risk assessment contains
- Personal protective equipment in plain terms
- Controls and hierarchy of control
- Health and safety abbreviations you will see
- Reading a safety data sheet
- Keeping the workplace safety glossary current
- Questions about health and safety terms
- What is the difference between a hazard and a risk?
- What does PPE stand for in health and safety?
- Where can I find an occupational health and safety terms definitions and abbreviations pdf?
- Is a risk assessment the same as a safety data sheet?
- Why do health and safety definitions use so many abbreviations?
- How often should a workplace safety glossary be updated?
Health and safety terms are the shared words a workplace uses to name danger, control it and record what was done. A health and safety glossary turns those words into short definitions you can apply at the counter, in the kitchen or on the floor. The abbreviations on signs, forms and policies shorten the same terms and need the same clear meaning.
- A hazard is the source of harm and a risk is the chance that harm occurs with its severity.
- A risk assessment records the hazards, who can be hurt and the controls you put in place.
- Personal protective equipment is the last line of defense, not a replacement for safer work.
- Abbreviations on signs and forms only help when the full term is written somewhere nearby.
- A written workplace safety glossary keeps terms and abbreviations used the same way by everyone.
Why a shared health and safety glossary matters
A health and safety glossary gives every worker the same meaning for the words used on signs, forms and briefings. Health and safety terms and definitions carry weight because they decide who acts and what gets recorded.
Workers at a seafood counter meet these terms in cleaning records, cold storage logs and knife handling instructions. Clear definitions stop a short form entry from being read two ways by two shifts.
An occupational health and safety glossary covers the workplace as a whole, not only the hazard in front of you. The same terms apply to storage rooms, delivery areas and service floors.
Hazard and risk are not the same term
A hazard is any source that can cause harm, such as a wet floor, a sharp blade or a spoiled product. Risk describes the chance that harm happens and how serious it would be.
Health and safety definitions keep hazard and risk apart because each one leads to a different action. You remove or reduce a hazard, and you judge the risk that remains.
Saying a hazard is high risk mixes two terms into one. State the hazard first, then describe the risk it creates for the people nearby.
What a risk assessment contains
A risk assessment is a written look at what could harm people and what you do to prevent it. The record names the hazard, who could be hurt and the controls already in place.
Risk assessment for a seafood counter covers slips, cold burns, knife cuts, bacterial growth and cleaning chemicals. Each hazard gets a control that fits the task, such as a drain cover, cut gloves or a labeled spray bottle.
A risk assessment is reviewed when the work changes, not filed once and forgotten. New equipment, a new product or a new layout can change the hazards and the controls.
- Name the hazard and where it occurs
- Identify who could be harmed
- Record the controls in place
- Decide if the remaining risk is acceptable
- Set a review point for the record
Personal protective equipment in plain terms
Personal protective equipment means the clothing and gear worn to shield a worker from a hazard. The term covers gloves, aprons, eye protection, safety footwear and cut resistant sleeves.
Personal protective equipment protects one person and only while it is worn and in good condition. Gear that is torn, loose or dirty stops doing its job.
Protective gear supports other controls but does not replace them. Guards on machines, clear walkways and safe work methods come before the apron and gloves.
Controls and hierarchy of control
The hierarchy of control ranks the ways of dealing with a hazard from the most reliable to the least. Eliminating the hazard sits at the top and protective gear sits at the bottom.
A control is any measure that removes a hazard or lowers the risk from it. Substitution replaces a dangerous item with a safer one, and engineering controls change the workplace itself.
Administrative controls change how people work, through training, rotation or procedures. They depend on people following them, so they stand below physical controls in the ranking.
Health and safety abbreviations you will see
Health and safety abbreviations are short forms built from the first letters of a term. PPE stands for personal protective equipment and RA stands for risk assessment.
SDS means safety data sheet and COSHH stands for control of substances hazardous to health in some regions. HACCP means hazard analysis and critical control points and applies to food safety planning.
Safety abbreviations save space on labels and forms, but an unfamiliar one causes confusion. Write the full term once on the document and pair the abbreviation with it everywhere else.
| Abbreviation | Full term |
|---|---|
| PPE | Personal protective equipment |
| RA | Risk assessment |
| SDS | Safety data sheet |
| HACCP | Hazard analysis and critical control points |
| OHS | Occupational health and safety |
Reading a safety data sheet
A safety data sheet carries the hazard information for a chemical product such as a sanitizer or degreaser. The document lists the hazards, handling advice, first aid steps and storage conditions.
The safety data sheet belongs with the product and stays readable for every shift. A worker who decants a chemical into a spray bottle needs the sheet and a labeled container.
Chemical hazards on a seafood counter include burns, fumes and reactions with other cleaners. Storage away from food and separate from other products prevents a dangerous mix.
Keeping the workplace safety glossary current
A workplace safety glossary stays useful when it is reviewed against the terms people actually use. New equipment brings new words, and old entries can fall out of step with the work.
The glossary should match the wording on signs, forms and training material across the site. One term with two spellings or two meanings causes a record to be misread.
Training sessions are the place to explain a new term and its abbreviation. A short written note beside each entry helps a new worker find the meaning fast.
Questions about health and safety terms
What is the difference between a hazard and a risk?
A hazard is a source of harm, while a risk is the chance and severity of harm from that hazard. The two health and safety terms are linked but not interchangeable. You identify the hazard and then assess the risk it creates.
What does PPE stand for in health and safety?
PPE stands for personal protective equipment, the gear worn to shield a worker from a hazard. Gloves, aprons and eye protection are examples of personal protective equipment. It sits at the bottom of the hierarchy of control and supports other measures.
Where can I find an occupational health and safety terms definitions and abbreviations pdf?
A workplace safety glossary compiled by a safety authority or a training body is the place to look for such a document. Check that the file covers occupational health and safety terms used in your own work. Keep the downloaded file with your other safety records.
Is a risk assessment the same as a safety data sheet?
No, a risk assessment and a safety data sheet are different documents with different jobs. A risk assessment records the hazards and controls for a task in your workplace. A safety data sheet supplies the hazard information for a chemical product.
Why do health and safety definitions use so many abbreviations?
Abbreviations shorten long terms that appear again and again on signs, labels and forms. Each health and safety abbreviation stands for a full term that should be written out once on the document. Unfamiliar abbreviations should always be spelled out for new workers.
How often should a workplace safety glossary be updated?
A workplace safety glossary should be updated whenever the work, the equipment or the products change. There is no fixed interval that fits every workplace, so set a review point that matches your own operations. Review the full list after any new hazard is found.